Welcome to the bigboi Knowledge Base
Your Source for Expert Advice, Troubleshooting, and Product Information
-
SuckR PRO
- WashR FLO pump is very noisy
- WashR FLO Water is leaking from the pump
- Storage and Transportation of the SuckR PRO
- Why Is My Engine Housing Overheating?
- Why Is the Suction Weakening?
- How to Assemble the SuckR PRO
- How to Service the SuckR PRO
- How to Use the Extraction Function (Kit Sold Separately)
- How to Use the SuckR PRO Vacuum Function (Wet & Dry)
- SuckR PRO Manual
-
WashR PRO
- The WashR PRO has a oil leak
- The WashR PRO is experiencing a water leak
- The WashR PRO motor does not start when switched on
- The WashR PRO pressure drops during use
- The WashR PRO Pressure fluctuates
- The WashR PRO pump is noisy
- The WashR PRO pump is running but does not reach the working pressure
- The WashR PRO When I switch on the unit, the motor hums but does not run
- There is the presence of water in oil on the WashR PRO
- Wash PRO TSS Version only. The motor starts even with gun trigger is released
- WashR PRO TSS Version only. No water delivery when gun trigger is depressed
- How to Adjust your Spray Pressure on the WashR PRO
- How to maintain your WashR PRO
- How to store your WashR PRO
- How to use your Nozzles with WashR PRO
- How to check your oil level before use?
- How to Setup the WashR PRO
- How to Start your WashR PRO
- How to Stop Your WashR PRO
- WashR PRO Manual
- The WashR FLO Motor refuses to start
- WashR FLO Does not reach high enough pressure
- WashR FLO Motor starts up but there is no working pressure
- WashR FLO motor stops
- WashR FLO No detergent present
- WashR FLO Output pressure varies high and low
- WashR FLO Spray wand is leaking
- How to Set Up the WashR FLO
- How to Turn On and Off Your WashR FLO
- WashR FLO Maintenance Guide
- WashR FLO Manual
Table of Contents
WashR FLO Maintenance Guide
Table of Contents
Regular maintenance of your Bigboi WashR FLO ensures its longevity and optimal performance. Follow these guidelines to keep your pressure washer in top condition.
Maintenance Steps
-
Check for Defects
- Regularly check for obvious defects such as loose fittings, and worn or damaged components.
-
Inspect Covers and Guards
- Ensure the covers and guards are undamaged and correctly fitted. Carry out necessary maintenance or repairs before using the washer.
-
Strainer Use
- Never use the pressure washer without the strainer or with a damaged strainer.
-
Transporting the Washer
- To transport the washer up or down obstacles, lift it by the top handle.
- If the washer is to be stored or transported horizontally, drain the detergent tank first.
-
Cleaning the Exterior
- Clean the exterior of the machine thoroughly using a soft brush or cloth. DO NOT use water, solvents, or polishes. Remove all debris, especially from the ventilation slots.
-
Cleaning the Nozzles
- Regularly clean the nozzles to ensure efficient running of the washer. The nozzle must be cleaned at regular intervals with the nozzle cleaner pin as provided.
-
Servicing and Repairs
- All pressure washers will eventually require servicing or replacement of parts due to wear from regular use. To ensure that only authorized replacement parts are used, all service and repairs must be performed by Bigboi authorized service centers.
By following these maintenance steps, you ensure your WashR FLO operates efficiently and safely. If you encounter any issues, refer to our troubleshooting guide or contact our support team for assistance.
Updated on 25 Jun 2024
What are your Feelings?
Thanks for your feedback
- Choosing a selection results in a full page refresh.