Welcome to the bigboi Knowledge Base
Your Source for Expert Advice, Troubleshooting, and Product Information
-
SuckR PRO
- WashR FLO pump is very noisy
- WashR FLO Water is leaking from the pump
- Storage and Transportation of the SuckR PRO
- Why Is My Engine Housing Overheating?
- Why Is the Suction Weakening?
- How to Assemble the SuckR PRO
- How to Service the SuckR PRO
- How to Use the Extraction Function (Kit Sold Separately)
- How to Use the SuckR PRO Vacuum Function (Wet & Dry)
- SuckR PRO Manual
-
WashR PRO
- The WashR PRO has a oil leak
- The WashR PRO is experiencing a water leak
- The WashR PRO motor does not start when switched on
- The WashR PRO pressure drops during use
- The WashR PRO Pressure fluctuates
- The WashR PRO pump is noisy
- The WashR PRO pump is running but does not reach the working pressure
- The WashR PRO When I switch on the unit, the motor hums but does not run
- There is the presence of water in oil on the WashR PRO
- Wash PRO TSS Version only. The motor starts even with gun trigger is released
- WashR PRO TSS Version only. No water delivery when gun trigger is depressed
- How to Adjust your Spray Pressure on the WashR PRO
- How to maintain your WashR PRO
- How to store your WashR PRO
- How to use your Nozzles with WashR PRO
- How to check your oil level before use?
- How to Setup the WashR PRO
- How to Start your WashR PRO
- How to Stop Your WashR PRO
- WashR PRO Manual
- The WashR FLO Motor refuses to start
- WashR FLO Does not reach high enough pressure
- WashR FLO Motor starts up but there is no working pressure
- WashR FLO motor stops
- WashR FLO No detergent present
- WashR FLO Output pressure varies high and low
- WashR FLO Spray wand is leaking
- How to Set Up the WashR FLO
- How to Turn On and Off Your WashR FLO
- WashR FLO Maintenance Guide
- WashR FLO Manual
Table of Contents
-
Step by Step Guide
- Position the Pressure Washer
- Check Connections
- DO NOT run the pump without the water supply connected and turned on.
- Damage to equipment resulting from failure to follow this instruction will VOID WARRANTY.
- Level Position
- Uncoil Hose
- Connect Garden Hose
- Purge Air and Impurities
- Attach Gun Lance
- Choose and Attach Nozzle
- Start the Motor
- Total Stop System (TSS)
How to Start your WashR PRO
Table of Contents
-
Step by Step Guide
- Position the Pressure Washer
- Check Connections
- DO NOT run the pump without the water supply connected and turned on.
- Damage to equipment resulting from failure to follow this instruction will VOID WARRANTY.
- Level Position
- Uncoil Hose
- Connect Garden Hose
- Purge Air and Impurities
- Attach Gun Lance
- Choose and Attach Nozzle
- Start the Motor
- Total Stop System (TSS)
Starting your Bigboi WASHR PRO for the first time, or after it has been idle for at least a day, is straightforward. Follow these step-by-step instructions:
Step by Step Guide
-
Position the Pressure Washer
- Place the pressure washer near an outside water source capable of supplying water at a flow rate of at least 5GPM (19LPM) and no less than 20PSI (1.3BAR) at the pressure washer end of the garden hose.
-
Check Connections
- Ensure the high-pressure hose is tightly connected to both the spray gun and the pump.
DO NOT run the pump without the water supply connected and turned on.
Damage to equipment resulting from failure to follow this instruction will VOID WARRANTY.
-
Level Position
- Make sure the unit is in a level position.
-
Uncoil Hose
- Completely uncoil the high-pressure hose before using the pressure washer.
-
Connect Garden Hose
- Connect the garden hose to the water inlet on the pressure washer pump.
-
Purge Air and Impurities
- Turn ON the water, point the gun in a safe direction, and squeeze the trigger to purge the pump system of air and impurities.
-
Attach Gun Lance
- Attach the gun lance to the spray gun. Ensure the connection is tight by pulling on the lance to confirm it is secure.
-
Choose and Attach Nozzle
- Choose the nozzle you want to use. Pull back on the collar of the quick connector, insert the nozzle, and release the collar. Tug on the nozzle to ensure it is securely in place.
IMPORTANT: Before starting the pressure washer, ensure you are wearing adequate safety equipment.
-
Start the Motor
- Press "ON" to start the motor.
NOTE: The cleaner must be used standing on a secure, stable surface, positioned as shown.
Total Stop System (TSS)
- TSS Version: The pressure pump unloader is built-in with the pressure switch. When the trigger is released for more than 5 seconds, the motor stops running and the controller enters STAND BY mode.
- Resuming Operation: When the trigger is squeezed, the motor will resume operation.
- Automatic Cut-off: If the pressure washer is in STAND BY mode for more than 30 minutes, the motor controller will automatically cut off and completely stop the system. DO NOT leave the pressure washer unsupervised when in STAND BY mode.
By following these steps, you ensure your WASHR PRO is started correctly and safely. If you encounter any issues, refer to our troubleshooting guide or contact our support team for assistance.
Updated on 25 Jun 2024
What are your Feelings?
Thanks for your feedback
- Choosing a selection results in a full page refresh.